Steroids Forum

Anabolic Steroids and Bodybuilding Online Board


always that little bubble in pin that I can't get out!

Share
avatar
MrFortlauderdale

Posts : 9
Karma : 13
Join date : 2016-02-22

always that little bubble in pin that I can't get out!

Post by MrFortlauderdale on Mon Oct 09, 2017 12:49 pm

I dont' get it... its so tiny... I flick and flick and flick.. and inject alittle and im wasting gear cause the bubble wont' dissapear.. any advice
avatar
w000dy
VIP
VIP

Posts : 77
Karma : 83
Join date : 2016-01-12
Age : 31
Location : Tennessee

Re: always that little bubble in pin that I can't get out!

Post by w000dy on Mon Oct 09, 2017 1:29 pm

If it's just a small bubble bro you will be ok. Just always aspriate to make sure you are not in a vien or blodd vessel and if not go on with the inject. I had the little tiny bubble in there many times I injected and came out fine.


_________________
Because we do not know when we will die, we get to think of life as an inexhaustible well, and yet everything happens only a certain number of times ... How many more times will you remember a certain afternoon of your childhood ... that is so deeply a part of your being that you can't even conceive of your life without it? Perhaps 4 or 5 times more. Perhaps not even. How many more times will you watch the full moon rise? Perhaps 20. And yet it all seems limitless.
-Brandon Lee-
avatar
BuffD

Posts : 77
Karma : 77
Join date : 2016-02-02
Location : In Dieselgirl's pants.

Re: always that little bubble in pin that I can't get out!

Post by BuffD on Mon Oct 09, 2017 2:08 pm

It's ok bro, You actually have to inject a decent amount of air into a vein to do any harm. A bubble or two won't do it and you shouldn't be going into a vein anyway.


_________________
Forecast for tomorrow- A few sprinkles of genius with a chance of DOOM!- Stewey Griffin
avatar
MrFortlauderdale

Posts : 9
Karma : 13
Join date : 2016-02-22

Re: always that little bubble in pin that I can't get out!

Post by MrFortlauderdale on Mon Oct 09, 2017 3:07 pm

thanks guys... I never used to have a problem with the splins bout 3-4 years ago with my first couple cycles... but now it just freaks me out man... too cautious I guess... damn... 10 more weeks of this shit! lol
avatar
zambon

Posts : 38
Karma : 38
Join date : 2016-02-08
Location : mid west

Re: always that little bubble in pin that I can't get out!

Post by zambon on Mon Oct 09, 2017 3:57 pm

Bump everyone else..no problem...google some medical sites about injecting air and you will see theres nothing to sweat if you follow simple steps. may put your worries to ease some.

agentsmith

Posts : 1
Karma : 1
Join date : 2017-10-09

Re: always that little bubble in pin that I can't get out!

Post by agentsmith on Tue Oct 10, 2017 12:29 am

If I,m not misteaken it takes about 3.6 cubic feet of air to be lethal and if you aspirate correctly, then some tiny bubbles shouldnt worry ya at all. hope that helps
avatar
Body2see

Posts : 16
Karma : 18
Join date : 2016-01-22

Re: always that little bubble in pin that I can't get out!

Post by Body2see on Tue Oct 10, 2017 1:02 am

The trick to it is to withdraw the oil about an inch or half a CC from the top prior to injecting. Let it sit for about 30minutes, and prior to letting it sit, really give it a good few flicks. Let it sit, then bring it back to the top...At this point, not even small bubbles will exist. This method really works.
avatar
750GSXR

Posts : 30
Karma : 40
Join date : 2016-03-16
Age : 36
Location : City Of Sin

Re: always that little bubble in pin that I can't get out!

Post by 750GSXR on Tue Oct 10, 2017 1:49 am

My suggestion is pre-load your pins for the week and then when you are ready to use just stand the pin in a glass of hot water needle side up and as the oil is heated and thins the air bubles rise then flick it. the thicker the oil the harder it is for the bubbles to comeout.It also helps if you heat up vial in hot water also it will cause less air bubbles when drawing.I get an air bubble that gets right up to the back of the needle,so I flick the barrell as I push on the plunger until the gear comes out and so does the bubble. Good luck


_________________
IF I CAN'T FIND A WAY I'LL MAKE ONE!!
avatar
irishpride0769

Posts : 77
Karma : 89
Join date : 2016-01-14

Re: always that little bubble in pin that I can't get out!

Post by irishpride0769 on Tue Oct 10, 2017 2:45 am

BuffD wrote:It's ok bro, You actually have to inject a decent amount of air into a vein to do any harm. A bubble or two won't do it and you shouldn't be going into a vein anyway.

i believe its about 3ccs of air to kill youi could be wrong though


_________________
I REALLY WISH I WAS CANADIAN!!!

Here Gerbil..Gerbil..Gerbil! Come to daddy!

I use Maxoderm for all my farm yard fun!
avatar
BuffD

Posts : 77
Karma : 77
Join date : 2016-02-02
Location : In Dieselgirl's pants.

Re: always that little bubble in pin that I can't get out!

Post by BuffD on Tue Oct 10, 2017 3:33 am

750GSXR wrote:My suggestion is pre-load your pins for the week and then when you are ready to use just stand the pin in a glass of hot water needle side up and as the oil is heated and thins the air bubles rise then flick it. the thicker the oil the harder it is for the bubbles to comeout.It also helps if you heat up vial in hot water also it will cause less air bubbles when drawing.I get an air bubble that gets right up to the back of the needle,so I flick the barrell as I push on the plunger until the gear comes out and so does the bubble. Good luck



I don't personally like to preload pins for that long due to contamination. Once the pin is opened and uncapped bacteria is in and can grow. Letting it sit for that long just lets it breed and get worse. The air isn't a big enough deal to make preloading worth it.


_________________
Forecast for tomorrow- A few sprinkles of genius with a chance of DOOM!- Stewey Griffin

Sponsored content

Re: always that little bubble in pin that I can't get out!

Post by Sponsored content


    Current date/time is Sat Oct 21, 2017 5:33 am